$23 Backup/Front/Side View Camera: No Distortion Effect Starlight Ni Electronics Car Vehicle Electronics Car Electronics Backup/Front/Side,Camera:,Ni,No,Starlight,$23,/basketwork1183040.html,alvinschang.com,Electronics , Car Vehicle Electronics , Car Electronics,Distortion,Effect,View Backup/Front/Side,Camera:,Ni,No,Starlight,$23,/basketwork1183040.html,alvinschang.com,Electronics , Car Vehicle Electronics , Car Electronics,Distortion,Effect,View Backup Front Side View Spasm price Camera: Ni No Effect Distortion Starlight Backup Front Side View Spasm price Camera: Ni No Effect Distortion Starlight $23 Backup/Front/Side View Camera: No Distortion Effect Starlight Ni Electronics Car Vehicle Electronics Car Electronics

Backup Front Side View Spasm price Camera: Ni Department store No Effect Distortion Starlight

Backup/Front/Side View Camera: No Distortion Effect Starlight Ni

$23

Backup/Front/Side View Camera: No Distortion Effect Starlight Ni

|||

Product Description

As a burgeoning manufacturer of top-notch OEMamp;ODM vehicle electronic products, NATIKA aims to serve even the most demanding needs of worldwide clientele.Invariably, we believe that customer experience counts far more than short-term profits, so we make concerted efforts to design, manufacture, and improve our products and services in an innovative and responsible fashion.

NATIKA backup camera WD-012 support flush or bracket mount option, no distorted amp; fish-eye effect, starlight level night vision,IP69K IP rating reliable waterproof and horizontal 135 degrees wide view angle.

Useful Wire/Loop Control Design:

Reverse camera WD-012 with 2 small wires/Loops (White and Green color).

*If you need the guide line, please keep the green loop; If no need, just cut it; If you use it as a front view camera, please cut the white loop;

*If you use it as a front view camera without guide line, please cut both white and green wire/loop; If as a side view camera, please rotate the middle housing part of the camera (maximum 360 degrees) to get a prefer view angle; Look backward, keep the white loop; look forward, cut the white loop.

*Note: this camera is a rear view camera with guide line/parking line as DEFAULT.

*Please power on again after you cut the small loops, then the image should be correct.

What you get:

1 x NATIKA Backup Camera; 1 x 26ft/8M Extension Wire; 2 x 304 Stainless Screws; 1 x Double Tape; 1 x User Manual; 1 x Electrical Tape; 3 x Wire Clamps; 1 x Panel Remover; 7 x Zip Ties; 1 x NATIKA Gift Box; 1 x Thanks Card; 1 x 0.886in/22.5MM TCT Hole Saw; 1 x 304 Stainless Bracket; 1 x Metal Front Housing

Notes:

*This NATIKA rear view camera WD-012 is perfect for REAR, FRONT and SIDE view.

*If connect this NATIKA backup/front/side view camera WD-012 to a FACTORY RADIO, please separately order a suited Harness amp; Programmer to complete installation, because different RADIO need different Harness amp; Programmer to work together.

* Mount this reverse camera on the panel and route the wire to inside (DO NOT pinch the wire/cable when route the wire, pinched wire will damage the camera, drill a hole to allow the wire go through if needed).

* If your head unit with a reverse triggering wire, normally it is a purple/white, blue/white or pink color wire, please find it, and connect it with the extension wire's triggering wire well(small short red wire next to the RCA/AV connector).

"p" *If the image on the screen is blurry, flickering/flash or has horizontal or vertical strip, please check all your power and video connections. Possibly use a different ground point(iron part) and wrap power and video plugs with electrical tape to insulate from interference. If it still with blurry, flickering/flash or has horizontal or vertical strip, please order a 12V DC power adapter filter rectifier to solve it, especially need for Dodge VW AUDI BMW Mercedes Benz brands vehicle.

"p" *Before you routing, if there is no image on the screen, other than check the camera, please check display setting as well. You can use other device with RCA connector, such as TV to check if the camera works.

"p" * If you use wire clamps for connection, please kindly check and see if it works(connection is solid or not).

"p" *For camera connection: connect the camera's male plug to female connector of the extension wire/cable, make sure the arrows to align and push the camera's male plug tightly into the female connector of the extension wire.

*If the camera is mounted offset, the guidelines on image will be offset.

*Ideally to mount the camera at the middle of the trim. If mount the camera at side, it still works, but with guide line offset.

*Guide line is for reference only, please use the mirrors for position when backup.

*Apply electrical tape for the joint of all for the connectors, and use zip ties to fasten the wire on your vehicle.

*Seal the red wire next RCA/AV connector with electrical tape if you do not use it.

*If you want to get a perfect view angle, before you use a drill rig to make a hole, please seriously check and test to find where is the best spot to mount this reverse camera,please rotate the middle housing part of the camera (maximum 360 degrees) or move the bracket (maximum 90 degrees) to get the best view angle.

backup camera for carbackup camera for car
back up camera for trucksback up camera for trucks

Backup/Front/Side View Camera: No Distortion Effect Starlight Ni